Krystol Internal Membrane (KIM) is a hydrophilic crystalline admixture used to create permanently waterproof concrete. Optional Krytonite waterstops and adhesive can be added to serve a wide range of applications.

Kryton Krystol Internal Membrane™ (KIM®):

A hydrophilic crystalline admixture internationally known for making exceptionally durable and watertight concrete.
Contains advanced Krystol® technology, which drives a catalytic reaction using cement and water to grow a protective crystalline network throughout the concrete’s pores, capillaries, cracks, and micro-cracks.
Long-term reactivity provides adaptive self-sealing and self-healing properties that counteract deterioration and allow concrete to maintain its integrity.
Non-toxic and meets all requirements of ACI 212.3R as a Permeability Reducing Admixture for Hydrostatic Conditions (PRAH).

Performance Requirements

1. Permeability: Reduced vs. untreated concrete when tested to modified BS EN 12390-8 (Taywood Valenta). Control 4.29 x 10^-14 m/s, treated 1.28 x10^-14m/s.

2. Compressive Strength: Equal or higher compressive strength when tested to BS EN 12390-3.

3. Flexural Strength: Equal or higher compressive strength when tested to BS EN 12390-5.

4. Slump: No change in slump class compared to untreated mix when tested to BS EN 12350-2.

5. Air Content: Max 2% above untreated mix when tested to BS EN 12350-7.

6. Drying Shrinkage, Reduced vs. untreated concrete when tested to BS 1881-5. Control value 0.040%, treated concrete 0.030%.

7. Wetting Expansion, Reduced vs. untreated concrete when tested to BS 1881-5. Control value 0.030%, treated concrete 0.020%.

8. Resistance to freeze-thaw expansion, reduced vs. intreated concrete when tested to BS 5075-2. Control value 0.742, treated concrete 0.099.

9. Water soluble chloride ion content; max 0.1% by weight.

10. Bond to steel (BBA internal method T1/19) - Pass

11. VOC content – 0 g/L

Quality Control Documents

1. BBA Certificate 05/4217

2. Factory Production Control Certificate 14/F086

Permeability:

1. When tested to BS EN 12390-8 or DIN 1048-5 at <0.5 MPa><<72.5 psi>> for 72 hours, the permeability of treated concrete will be reduced by 70% over untreated concrete.

2. When using the Taywood / Valenta method of testing to modified BS EN 12390-8 at <1 MPa><<150 psi>> for 96 hours and then measuring and calculating the coefficient of permeability, the permeability of treated concrete will be reduced by a minimum of 70% over untreated concrete.

3. When tested to USACE CRD C48, no passage of water through treated samples when exposed to a vertical water head equal to 200 psi (460 foot head pressure) for 14 days.

4. When tested to USACE CRD C48, treated samples exposed to a vertical water head equal to 200 psi (460 foot head pressure) for 14 days will show a reduced coefficient of permeability of 97%.

B. Compressive Strength: Treated concrete must have compressive strength equal or higher than plain concrete when tested to ASTM C39/C39M at 28 days.

C. Drying Shrinkage: Minimum 20% reduced drying shrinkage for treated concrete when tested to ASTM C157.

D. Self-Sealing: Autogenous crack sealing of treated concrete for cracks with width of <0.5mm><<0.02 inches>> or greater; verified by independent testing.

E. Chemical Resistance: The waterproofing admixture shall improve sulphuric acid resistance of cement-based materials by blocking capillary pores to reduce acid penetration.

F. Corrosion of Reinforcing Steel:

1. Field Performance - The waterproofing admixture must provide enhanced corrosion resistance to embedded steel such that low half-cell readings and no noticeable signs of corrosion are evident after 10 years exposure directly in the corrosive marine tidal zone whereas untreated panels show evidence of corrosion.

2. Testing following ASTM G109 and ASTM C876, and assessed using half-cell measurements, macro cell corrosion rate, and lineral polarization resistance (LPR) after exposure to severe corrosive conditions, must demonstrate that the waterproofing admixture significantly delays the onset of corrosive conditions and reduces corrosion rates.

G. Evidence of Crystallization:

1. Manufacturer must present independent evidence of waterproofing crystals using both optical imaging and scanning electronic microscope (SEM) to verify waterproofing crystals are needle-shaped.

2. The manufacturer must present independent evidence using Energy Dispersive X-Ray Spectroscopy (EDS) that waterproofing crystals are distinct from ettringite crystals.

H. Bonding of coatings and finishes – Manufacturer must present tensile pull-off testing showing that the waterproofing admixture does not reduce the bond strength of subsequent coatings or finishes, with examples of using four different coatings (acrylic coating, rubber coating, epoxy coating, and tile thin-set).

Krytonite™ Swelling Waterstop:

High performance elastomeric waterstop made from hydrophilic synthetic rubber.
Available in standard or rain-protected versions.
Delivers high performance waterproofing in a cost effective and easy to install solution.
Uses swelling pressure to seal concrete construction joints and penetrations to stop water in the most extreme conditions.
Extremely durable and will not deteriorate over time.
Contains NO bentonite.
Designed to replace moulded PVC waterstops and bentonite-based waterstops.
Krytonite can also be used by itself as a single protection waterstop.

Smart Bond Adhesive:

Specially designed to adhere Krytonite™ Swelling Waterstop to concrete construction joints and penetrations that require waterproofing.
Has incredible bonding strength, even on damp concrete surfaces and can be used in all seasons.
Adhesive
Permanent elasticity
Does not cause staining on natural stone
High resistance to UV
Suitable for dry and humid weather conditions
Fast build-up of internal strength. The glue obtains most of its final strength already after a couple of hours
High end strength
Does not cause any corrosion in metal joints
Paintable with most water and solvent based paints
Solvent, isocyanate and phthalate free

Consult manufacturer's literature for application examples.